How to Reset a Router to Factory Default (Button and Web Methods)

By Madan Kc, ISP/GPON engineer at DG Link Network · Updated 9 November 2026 · 8 min read

Quick answer: With the router powered on, press and hold the recessed Reset button with a paperclip for about 10 seconds (some models need up to 30) until the LEDs blink or all go out, then release and wait 2–5 minutes. Everything you configured, including the Wi-Fi name and password, admin password and internet (PPPoE) settings, is erased. If you can still log in, resetting from the web page is safer.

When to reset (and when not to)

A factory reset is a last-but-one resort. Try a reboot first: unplug the power for 30 seconds and plug it back in. A reboot keeps every setting; a reset wipes them.

Reboot vs factory reset
ActionWhat it doesSettings kept?
RebootRestarts the router, like restarting a PCYes
Factory reset (button or web)Erases the saved configuration and loads the factory oneNo

Reset when you forgot the admin password, you bought a used router, the web page will not load even by cable, or you want to start clean after changing ISP. Do not reset just because the Wi-Fi is slow; see why your internet is slow first.

Before you reset

You will lose: Wi-Fi name and password, admin password, internet settings (PPPoE username and password, VLAN, static IP), port forwarding, DHCP reservations, parental controls and firewall rules.

What to write down first
ItemWhere to find it
Internet login (PPPoE username/password, or VLAN ID)Your ISP, or the router’s WAN page if you can still log in
Wi-Fi name and passwordRouter label, or read it from a connected PC
Default IP, username, passwordSticker on the bottom of the router
Port forwarding and static IP listsScreenshot each page

If you only forgot the Wi-Fi password, you may not need a reset at all: see forgotten Wi-Fi password.

Method 1: Reset button (works without the password)

  1. Keep the router powered on and wait until the power LED is steady.
  2. Find the Reset button. It is usually a small hole on the back or bottom marked RESET or RST. Do not confuse it with WPS.
  3. Push a straightened paperclip into the hole and hold it for about 10 seconds. Many models want 5–15 seconds; a few ISP units want 30.
  4. Watch the LEDs: they usually all flash or go dark at the moment the reset fires. Release then.
  5. Wait 2–5 minutes without touching the power. Interrupting the reboot can corrupt the firmware.
  6. Connect by cable or to the default Wi-Fi name printed on the label and open the default IP (often 192.168.1.1, 192.168.0.1 or 192.168.100.1). See 192.168.1.1 login if the page will not open.

Method 2: Web page reset

  1. Log in at the router IP with your admin account.
  2. Open the system or administration menu. It is usually called Factory Defaults, Restore Factory Settings, System Tools or Backup & Restore.
  3. Choose restore or reset, confirm, and wait 2–5 minutes while the router restarts.

Some routers let you save a configuration backup first. Do that if the option exists; restoring it later saves the reconfiguration.

Brand notes

Button positions and defaults vary by model and firmware. The label on your unit always wins over the table below.

Typical reset details by brand
BrandWeb path (typical)Address after resetLogin after reset
TP-LinkSystem Tools → Backup & Restore / Factory Defaultstplinkwifi.net or 192.168.0.1Older: admin/admin. Newer models ask you to create a password. See TP-Link default password
ASUSAdministration → Restore/Save/Upload Settingrouter.asus.com or 192.168.1.1Setup wizard asks for a new login
NetgearAdvanced → Administration → Backup Settingsrouterlogin.netadmin / password on older firmware
D-LinkTools or Maintenance → System192.168.0.1Often admin with a blank password. See D-Link default password
MikroTikSystem → Reset Configuration192.168.88.1admin, blank password. See 192.168.88.1 login
Huawei mobile Wi-Fi / 4GSettings → System → Restore192.168.8.1See 192.168.8.1 login

Cisco routers (CLI)

Cisco IOS routers have no Reset button procedure like home routers. Erase the saved configuration and reload:

Router# write erase
Router# reload

Answer no if asked to save the modified configuration. The config-register 0x2142 trick is for password recovery, not a factory reset, so do not use it for this.

ISP-supplied routers and ONTs

Careful with fiber ONTs: On a GPON/EPON ONT or router from your ISP, a reset can remove the VLAN, PPPoE and management settings the ISP configured, and the line may stay offline until the ISP re-provisions it. Call your ISP first, and keep the PPPoE details ready. Some ISPs push the configuration back automatically; many do not.

If the unit is yours and you only need to change the Wi-Fi name or password, do that in the web page instead of resetting. For Huawei units see Huawei router Wi-Fi password change.

After the reset

  1. Log in with the default credentials from the label.
  2. Set the internet connection (PPPoE or DHCP, as your ISP specifies) and confirm you get online.
  3. Set a new Wi-Fi name and a WPA2 or WPA3 password.
  4. Change the admin password right away. Default logins are public knowledge.
  5. Update the firmware, then re-add port forwarding such as on a TP-Link router.
  6. Reconnect your devices, forgetting the old network entry first if the name is the same.

Problems

The Reset button does nothing

Hold longer (up to 30 seconds), make sure the router is powered on, and press the Reset hole, not WPS. If it still fails, use the web method, or the button may be faulty.

I cannot open the router page after the reset

Use a LAN cable, check the label for the real default IP, and make sure your PC is set to obtain an IP automatically. Try another browser. If the IP is unknown, check the PC’s default gateway with ipconfig (Windows).

The lights never came back

Wait 10 minutes, then power-cycle once. If it stays dead, the firmware may be corrupt and the router may need a recovery tool from the manufacturer.

FAQ

How long should I hold the Reset button?

About 10 seconds for most home routers. Some need 5 seconds, others 30. Release when the LEDs flash or turn off.

Will a factory reset remove my internet connection?

Yes, until you enter the ISP settings again. On ISP-provided ONTs it can also remove the provisioning, so call the ISP first.

Can I reset without knowing the admin password?

Yes. The physical Reset button does not need a password.

Does a reset remove malware?

It clears the saved configuration, which fixes most hijacked DNS or settings. It does not fix an old, vulnerable firmware, so update the firmware afterwards and change the admin password.

Can unplugging during a reset damage the router?

It can corrupt the firmware on some models. Let the router finish rebooting before touching the power.

Need help with an ISP or router problem? Contact me with the router model and what you see.

Related guides

Sources and testing: steps reflect common router behaviour and my work on ISP routers and ONTs. Button timings and default logins differ by model and firmware, so check the label and manual for your exact unit. I did not test every brand listed.